Washing machine water inlet valve: signs of failure, testing and replacement
The water inlet valve (also called the fill valve or solenoid valve) sits at the back of the machine, near the top — the fill hose screws straight onto it. It is an electromagnetic valve: until its coil is energised it stays closed and holds back the mains pressure. When the programme needs water, the control board powers the coil, the valve opens and water runs through the detergent drawer into the drum.
On most machines the valve has several sections, each with its own coil. They open at different stages of the wash and send water to different parts of the drawer: prewash, main wash and softener. That is why the valve can fail only partly — for example, the machine fills for the wash but never flushes the softener.
At the valve inlet there is a small mesh filter. It catches sand, rust and scale from the pipes. A blocked filter is one of the most common reasons why a machine fills slowly or shows a fill error even though the valve itself is fine.
Signs of failure
- the machine does not fill at all or fills very slowly, and the programme stops;
- a fill error on the display: IE on LG, 4C/4E or nF on Samsung, E17 on Bosch and Siemens (F17 on Bosch), E10 on Electrolux, AEG and Zanussi, E02 on Beko, Vestel, Candy and Hoover, Err5 on Haier, F5 on Atlant, F10 on Miele;
- water comes in only at some stages: for example, the softener or the detergent in one drawer compartment is not flushed — one valve section has failed;
- the machine takes in water while it is switched off or after the wash has finished — the valve does not close fully;
- water rises above the normal level — the valve does not shut completely;
- water drips or leaks at the back, where the fill hose connects to the valve;
- the coil hums during filling, but no water comes in.
When this part fails: Not filling with water · Leaking water · Not taking detergent or softener · Takes too long
How it is checked
Start with the simple things: often the problem is the water supply, not the valve. Unplug the machine before checking — the valve carries mains voltage.
- Make sure there is water in the house and the machine's supply tap is fully open. If other taps also run weakly, the problem is the plumbing, not the machine.
- Check the fill hose: it must not be kinked or squashed, for example after the machine was pushed back against the wall.
- Close the tap, unscrew the hose from the machine, hold it over a bucket and open the tap again. Water should come out in a strong stream. If the flow is weak, the blockage is in the tap or the hose.
- Look at the mesh filter in the valve inlet (and in the hose end, if there is one). Pull it out gently with pliers and rinse it under running water. The filter is thin and brittle: if it has a hole, grit gets into the valve and stops it closing.
- Reconnect the hose, open the tap and check that the joint does not leak.
- If the machine fills while it is switched off, close the tap and keep it closed until the technician arrives. Also check the drain hose: if it is fixed too low, water can run back into the machine from the waste pipe on its own.
What the technician checks:
- the resistance of each valve section's coil with a multimeter — an open circuit (infinite resistance) or a short means the valve must be replaced;
- whether the valve gets voltage when the programme calls for water — if not, the cause is the wiring or the control board;
- whether the valve seat is fouled with grit or limescale and whether the valve closes fully;
- the water level sensor (pressure switch): if it is faulty, the machine may not start filling or may not know when to stop.
Repair and replacement
If the tap is open and the hose and filter are clear, but the machine still does not fill, keeps filling, or one section does not work, the valve needs replacing. It is usually not repaired; a new valve that matches the machine's model is fitted instead. The job is done on site, without taking the machine away. After fitting it, the technician runs a short programme and checks the joints for leaks.
Do not put the repair off if the valve does not close: water can overflow through the drawer onto the floor.
To make the new valve last longer:
- rinse the inlet filter at least a couple of times a year, especially if sand or rust comes through your pipes;
- after plumbing work or a water cut, run some water from another tap before starting a wash;
- close the supply tap if you are going away for a long time.
A MasService technician comes to your home anywhere in Baku, checks the valve, the wiring and the water level sensor and names the price before starting the work.
Error codes related to this part
Frequently asked questions
The machine fills with water on its own while it is off — is it the valve?
Often the valve does not close fully because of wear or grit in its seat. The other cause is a drain hose fixed too low, so water runs back from the waste pipe. Close the tap and call a technician.
Only the softener is not flushed — can the valve be to blame?
Yes. If the programme finished normally and the drawer is clean, the valve section that feeds the softener compartment has often failed. A technician measures that coil separately.
Can the valve just be cleaned?
The mesh filter at the inlet can be cleaned, and that often cures slow filling. If a coil has burnt out or the valve does not hold back the water, the whole valve is replaced.
Other parts
Washing machine repair — Brands
Could not fix it yourself? A technician comes to your home in Baku, finds the cause on site and names the price before the repair: Washing machine repair