Washing machine pressure switch: signs of failure, testing and replacement
The pressure switch is the water level sensor. It tells the control board when the tub has enough water and when it is empty after draining. Filling, heating and spinning all depend on this signal: for example, the board only switches the heating on once the sensor has confirmed there is water in the tub.
The switch does not measure the level directly but by air pressure. At the bottom of the tub there is a small chamber, and a thin tube runs from it up to the switch. As the water rises it compresses the air in the chamber and tube, and the switch operates. That is why the fault is more often in the chamber or tube than in the switch itself: detergent residue and dirt block the chamber, and the tube can crack, kink or come off. Newer machines use an electronic sensor instead of a mechanical switch, but the principle is the same.
Signs of failure
- the machine will not fill or stops filling too early — the switch reports that the tub is already full;
- the machine overfills: it takes in water and does not stop;
- the water has drained but the machine will not spin — the board thinks there is still water in the tub;
- the water does not heat, or the programme stops with an error;
- a water level sensor error: PE on LG, 1E on Samsung, F04 or F10 on Indesit and Ariston;
- an overflow error: FE on LG, OE on Samsung.
When this part fails: Not spinning · Not heating water · Not filling with water
How it is checked
The water level system is hidden inside the cabinet, so there is not much you can do yourself. But a few checks help tell a switch fault from other causes:
- If water keeps coming in even with the machine switched off, the pressure switch is not to blame — the inlet valve has jammed open. Turn off the tap and call a technician.
- If the machine will not fill, check that the tap is open and the inlet hose is not kinked, and clean the mesh filter at the hose inlet.
- If the machine has drained but will not spin, check the pump filter and drain hose: with poor draining the machine will not move on to the spin either.
- Do not try to bypass the switch to make the machine run past the error: the pressure switch is a safety device that stops the machine overfilling.
What the technician checks:
- the pressure switch tube: for cracks, kinks, ends that have come off and blockages;
- the chamber at the bottom of the tub: it is flushed of deposits — the most common cause of faults;
- the switch itself — only once the chamber and tube are clean and intact and the machine still misreads the water level;
- the connectors, wiring and the board that reads the switch signal.
Repair and replacement
Most often the repair comes down to cleaning the chamber and tube or replacing the tube — quick and done on site. The switch itself is replaced only if the machine keeps misreading the water level after cleaning. If the board misreads the signal, the board is repaired.
To keep the water level system from clogging:
- do not overdose detergent — the deposits in the chamber are mostly detergent residue and dirt;
- run the drum-clean programme or a hot wash without laundry from time to time.
A MasService technician comes to your home anywhere in Baku, checks the water level system, the inlet valve and the board, and names the price before starting.
Error codes related to this part
Frequently asked questions
The machine overfills — is it the pressure switch?
Most often the water level system is to blame: a blocked chamber, a cracked or loose tube, or the switch itself. But first switch the machine off: if water keeps coming in with the machine off, the inlet valve has jammed open.
Why will the machine not spin although the water has drained?
The board only allows the spin once the water level sensor confirms the tub is empty. If the chamber is blocked and holds pressure, the sensor keeps "seeing" water. Also check the pump filter and the drain hose.
Can I clean the pressure switch myself?
The tube and chamber are inside the cabinet: you need to unplug the machine and remove the top panel. If you are not experienced, leave it to a technician — a loosely fitted tube will leak air and the machine will misread the water level again.
Other parts
Washing machine repair — Brands
Could not fix it yourself? A technician comes to your home in Baku, finds the cause on site and names the price before the repair: Washing machine repair