Washing machine door seal: leaks, mould, cleaning and replacement
The door seal (door boot) is the folded rubber seal between the door and the tub of a front-loading washing machine. When the door is closed, its glass presses against the lip of the seal and the water stays inside the drum. The outer edge of the seal is clamped to the cabinet and the inner edge to the tub, so it flexes with the tub during washing and spinning.
A little water always stays in the folds of the seal, together with lint, hair, detergent residue and small things from pockets: coins, hair pins, bra underwires. Most of it collects at the bottom, at the six o'clock position. If the door is shut straight away, the moisture cannot dry, and dark mould spots and a bad smell appear on the rubber. Sharp objects and hard debris wear through or cut the rubber over time — and then water starts leaking from the front, under the door, during the wash.
Most seal problems are solved by cleaning. The seal is replaced when the rubber has a hole or a split, when the lip has hardened and lost its shape, or when mould has gone so deep that it will not clean off.
Signs of failure
- water leaks from the front, under the door, during the wash and not only while draining;
- a cut, hole or split is visible in the seal — often at the bottom or deep inside a fold;
- the lip the glass presses against has hardened, cracked or lost its shape;
- black mould in the folds does not go away after cleaning;
- the drum smells damp or mouldy even though the filter and the detergent drawer are clean;
- coins, hair pins, a bra wire or a sock are stuck in the fold;
- hair, lint or dried detergent is stuck between the lip of the seal and the glass.
When this part fails: Leaking water · Bad smell
How it is checked
You can check a lot yourself. Unplug the machine before you start.
- Make sure the water really comes from the seal. Water from an overfilled detergent drawer can run down the front panel and drip off the door — it looks like a seal leak, but the cause is different.
- Open the door and fold the seal back all the way round, especially at the bottom. Take out anything stuck in the fold: coins, hair pins, socks, wires.
- Look at the rubber and run a finger along all the folds and the lip. A small hole high up on the seal is easy to miss by eye and easier to find by touch.
- Wipe the lip of the seal and the inside of the glass: hair, lint or dried detergent between them can let water out even when the seal is intact.
- Check that no clothing is caught in the door, that the door closes with a click and that the drum is not overloaded. Dose detergent as the pack says — excess foam can also escape through the door.
- If there is mould on the seal, clean it with a mild cleaner the manufacturer allows, without abrasives. Then wipe it dry.
What the technician checks:
- the whole surface of the seal, including the part that runs inward to the tub;
- the condition of the lip and how tightly the door glass seals against it;
- how the seal and the clamps are seated — the outer clamp on the cabinet and the inner clamp on the tub;
- whether the water actually comes from the detergent drawer, the hoses or from under the tub — such leaks are easily mistaken for a seal leak.
Repair and replacement
If the seal has a hole or a split, the lip has hardened and distorted, or the mould will not clean off, the seal is replaced. Gluing it or covering it with silicone is not a good idea: the rubber flexes all the time and a patch does not last.
To replace it, the technician first removes the outer clamp — a spring wire ring or a band — then folds the seal back and releases the inner clamp that holds it on the tub. On many models the front panel comes off for this. The new seal is fitted exactly to its marks: the drain holes must be at the bottom, otherwise water collects in the fold. After fitting, the machine is tested on a rinse cycle to make sure nothing leaks at the front.
To keep the seal clean and intact for longer:
- wipe it dry after washing and leave the door ajar until the drum has dried;
- run a hot wash with the drum empty regularly — Electrolux recommends 60 °C or more for this;
- do not overdose detergent;
- check pockets, and wash underwired bras in a laundry bag;
- now and then fold the seal back and remove debris from the bottom fold.
A MasService technician comes to your home anywhere in Baku, checks the seal, the clamps and the other places a leak can come from, and names the price before starting the work.
Frequently asked questions
Why does mould grow on the door seal?
Water stays in the folds, and if the door is shut straight away it cannot dry. Frequent low-temperature washes and too much detergent help mould grow. Wipe the seal dry, leave the door ajar and run a hot wash with the drum empty from time to time.
Can a hole in the door seal be patched?
Not reliably. The seal flexes all the time during washing and spinning, and a patch or silicone soon comes away. A damaged seal is replaced as a whole.
Water leaks under the door but I see no hole — what else can it be?
Often it is debris between the lip of the seal and the glass, clothing caught in the door, too much foam or water running down from the detergent drawer. If all that is ruled out, a technician checks the seal by touch, the clamps and the internal connections.
Other parts
Washing machine repair — Brands
Could not fix it yourself? A technician comes to your home in Baku, finds the cause on site and names the price before the repair: Washing machine repair