Washing machine heating element: signs of failure, testing and replacement
The heating element heats the water to the temperature you choose in the programme. It sits at the bottom of the tub, under the drum. Next to it or built into it there is a temperature sensor (NTC): the electronics use it to know when the water is hot enough and the element should switch off.
An element usually fails for one of two reasons. The first is limescale: a layer of scale stops the heat from getting into the water, so the element overheats and burns out. The second is an insulation breakdown: the element starts leaking current to the casing, and the RCD or breaker trips while it heats. Below is how to recognise each case.
Signs of failure
- the water does not get hot: the door glass is cold 20–30 minutes into a 60 °C wash, laundry is not clean, detergent does not dissolve;
- the programme takes much longer than usual or stops at the heating stage;
- a heating error: HE on LG and Samsung, F19 on Bosch and Siemens, F07 on Indesit, E61 on Electrolux and AEG;
- the RCD or breaker trips a few minutes into a hot wash, while cold programmes run fine;
- after the RCD trips there is a smell of burnt insulation from the machine or the fuse box.
When this part fails: Not heating water · Trips the breaker or RCD · Takes too long
How it is checked
Only check what does not need dismantling:
- Make sure a programme with heating is selected: on a Cold wash, and on some eco programmes at a low temperature, the element hardly switches on.
- Start a 60 °C wash and after 20–30 minutes carefully touch the door glass: it should feel noticeably warm.
- Note when the RCD or breaker trips: if it only happens on hot programmes, current is probably leaking through the element.
- If the protection trips, do not switch the machine on again until it has been checked — this is an electrical safety issue.
What the technician checks:
- the element's resistance: an open circuit means it has burnt out. For a 2 kW element at 230 V the normal resistance is about 26 ohms (R = U²/P);
- the insulation between the element terminals and the casing. A normal multimeter often misses a small leak, so a 500 V insulation tester is used;
- the temperature sensor (NTC), the wiring and the heater relay on the board;
- the water level sensor: if the electronics "think" there is no water in the tub, they will not switch the heating on.
Repair and replacement
A burnt-out element or one with broken insulation is not repaired but replaced. Depending on the model it is reached through the back or the front panel; the replacement does not take long and is done on site. At the same time the technician checks the temperature sensor and the tub: heavy scale and dirt are removed.
To make the new element last longer:
- dose the detergent for your water hardness, as the manufacturer recommends;
- run the drum-clean programme now and then, or a hot wash without laundry with a suitable cleaner.
A MasService technician comes to your home anywhere in Baku, finds the cause — the element, the sensor or the board — and names the price before starting.
Error codes related to this part
Frequently asked questions
Why does the RCD trip only on hot washes?
Most likely the element insulation has broken down: when it is cold there is no leak, but as it heats up current leaks to the casing and the RCD trips. Better not to switch the machine on until it has been checked.
Can I wash in cold water until the element is replaced?
If the element has simply burnt out and nothing trips, cold programmes will run, but many machines stop with a heating error. If the RCD trips, do not use the machine until it is repaired.
Can limescale be cleaned off the element?
A light layer is removed by a cleaning programme with a suitable product. If the element has already burnt out or is covered in thick scale, it is replaced.
Other parts
Washing machine repair — Brands
Could not fix it yourself? A technician comes to your home in Baku, finds the cause on site and names the price before the repair: Washing machine repair