Washing machine motor: carbon brushes, speed sensor, signs of failure and repair

The motor turns the drum: slowly and alternately in both directions during the wash, fast during the spin. Washing machines use two main types of motor.

A brushed motor sits under the tub and turns the drum through a belt. Current reaches its rotating part through two carbon brushes pressed against the commutator — copper segments on the shaft. The brushes slowly wear down, and this is one of the most common reasons a drum stops turning. An inverter (brushless) motor, including direct drive, has no brushes, so there is nothing in it to wear out; its faults are more often in the drum mechanics, the wiring and the electronics.

The board monitors the drum speed with a speed sensor. On brushed motors this is a tacho generator: a small coil at the end of the motor with a magnet on the shaft spinning past it. If there is no signal from the sensor, the board stops the programme and shows an error.

Call now

Signs of failure

  • the machine fills and drains, the programme runs, but the drum stands still — a typical sign of worn brushes;
  • for a few weeks the drum turns weakly or in jerks, then stops altogether;
  • the machine will not spin or will not reach speed;
  • sparks are visible under the machine while it turns, there is a burning smell after a wash;
  • the motor hums but the drum does not turn — something is holding it: a foreign object, a bearing or the belt;
  • a motor error: 3E/3C on Samsung, LE or CE on LG, F21/E21 on Bosch and Siemens, E50 on Electrolux, AEG and Zanussi, F01 on Indesit and Ariston;
  • a speed sensor error: E52 on Electrolux, AEG and Zanussi, F02 on Indesit and Ariston;
  • the breaker or RCD trips — one possible cause is an insulation fault in the motor.

When this part fails: Not spinning · Trips the breaker or RCD · Drum does not turn

How it is checked

There is little you can check without dismantling, but it helps to narrow down where to look:

  1. Unplug the machine, open the door and turn the empty drum by hand. It should turn freely and quietly. If the drum is stuck or grinds, the motor is probably not to blame — look for a foreign object or worn bearings.
  2. If the machine will not spin, rule out an unbalanced load: with a single heavy item or a ball of laundry the machine may refuse to speed up.
  3. Run a Rinse programme and listen: if water comes in and drains but the drum stays still and the motor makes no sound, the brushes are probably worn or the motor is getting no power.
  4. If you see sparks under the machine or smell burning, switch it off and do not wash until it has been checked: sparking damages the motor's commutator.

What the technician checks:

  • the belt: whether it has come off or stretched;
  • the carbon brushes: if a brush has worn down to a stub — well under a centimetre — they are replaced;
  • the commutator: the copper segments should be smooth, without deep grooves or burn marks;
  • the tacho generator and its magnet, the connector on the motor and the wiring to the board;
  • the motor windings and their insulation to the casing;
  • the motor control section of the board: the triac, or on inverter machines the motor control board.

Repair and replacement

Worn brushes are replaced as a pair, even if one looks better: a new brush paired with an old one makes uneven contact and sparks. For the first few washes after the replacement the motor may smell slightly and run a little louder while the brushes bed in — this is normal.

If the belt has come off or a connector has lost contact, the repair is simple. A faulty speed sensor, a damaged commutator or a burnt winding is a bigger job: depending on the model the part or the whole motor is replaced, and the technician tells you in advance which makes more sense. If the board is to blame, its motor control section is repaired.

A MasService technician comes to your home anywhere in Baku, finds the cause — brushes, belt, sensor, motor or board — and names the price before starting.

Frequently asked questions

How do I know the brushes are worn?

The typical picture: the machine fills and drains, the programme runs, but the drum does not turn, or turns weakly and in jerks. Sometimes sparks under the machine and a burning smell come first. A technician can tell for sure by inspecting the brushes.

Do machines with an inverter motor have brushes?

No. Inverter motors, including direct drive, are brushless, so there are no brushes to wear out. If the drum on such a machine does not turn, the drum mechanics, the wiring and the motor control electronics are checked.

If one brush is worn, do both need replacing?

Yes. Brushes wear together and are replaced as a pair: a new brush working with an old one runs unevenly and sparks, and the commutator wears faster because of it.

Could not fix it yourself? A technician comes to your home in Baku, finds the cause on site and names the price before the repair: Washing machine repair

Call now WhatsApp