Dishwasher water inlet valve: how it works, signs of failure and how it is tested

The water inlet (fill) valve lets mains water into the dishwasher. It usually sits at the bottom, behind the lower front panel, and the inlet hose connects to it.

It is a solenoid valve. While its coil gets no power it stays closed and holds back the water pressure. When the programme needs water, the control board powers the coil, the coil opens a diaphragm and water flows in. When there is enough water, the power is cut and the valve closes.

Many valves have a small mesh screen at the inlet that catches sand and deposits from the pipes. A clogged screen is a common reason for slow filling or a water supply error even when the valve itself is fine.

Call now

Signs of failure

  • the dishwasher does not fill or fills very slowly, and the programme does not move on;
  • a water supply error on the display: IE on LG, 4E on Samsung, i10 on Electrolux, AEG and Zanussi, E16 or E18 on Siemens;
  • you hear a hum or a click during filling but no water comes in — the valve gets power but does not open;
  • it fills more than normal and the water rises above the heating element — the valve does not close fully;
  • it takes in water even when switched off;
  • a leak under the machine at the inlet hose connection or at the valve body.

When this part fails: Not cleaning dishes properly · Leaking water · Not filling with water

How it is checked

Start with the water supply: often the valve is not the problem. Before any check, unplug the dishwasher and turn off the water tap.

  1. Make sure there is water in the house and the dishwasher's supply tap is fully open — it is often forgotten after plumbing work or a holiday.
  2. Check the inlet hose: it must not be kinked or squeezed behind the machine or under the sink.
  3. Close the tap, disconnect the hose from the machine, hold it over a bucket and open the tap. The water should come out in a strong stream. A weak stream means a blockage in the tap or hose, or low pressure in the house.
  4. If there is a mesh screen at the valve inlet or in the hose end, rinse it carefully. The screen is thin: do not damage it.
  5. Reconnect the hose and check that the connection does not leak.
  6. If the machine overfills or takes in water while switched off, keep the tap closed until the technician arrives.

What the technician checks:

  • the resistance of the valve coil with a multimeter: an open circuit or a reading near zero means the coil has failed and the valve is replaced;
  • whether the valve gets voltage during filling: voltage but no water means a mechanical fault in the valve; no voltage points to the control board, the door switch or the wiring;
  • whether the valve closes: if water keeps coming in with the door open, the valve is stuck open;
  • the float and level switch: a stuck float also stops the dishwasher from filling.

Repair and replacement

Call a technician if the dishwasher still will not fill after you have checked the tap, hose and screen, if the water supply code keeps coming back, or if the machine overfills and takes in water while switched off. Bosch says that filling system errors that keep returning need an engineer.

A faulty valve is usually not repaired but replaced with one that fits the model. After the replacement the technician checks filling and leaks on a full programme.

A MasService technician comes to your home in any district of Baku, finds the cause and tells you the price before starting work.

Frequently asked questions

How do I know the dishwasher inlet valve is bad?

The dishwasher does not fill or fills slowly although the tap is open and the hose is fine, you hear a hum with no water, or the opposite — water keeps coming in, even with the machine switched off.

Can the inlet valve be cleaned?

The mesh screen at the inlet, if there is one, can be rinsed. If the coil does not work or the valve does not close, the valve is replaced as a whole.

Why does my dishwasher fill with water when it is off?

Usually the valve does not close fully because of wear or debris inside. Close the water tap and call a technician: the valve needs to be replaced.

Could not fix it yourself? A technician comes to your home in Baku, finds the cause on site and names the price before the repair: Dishwasher repair

Call now WhatsApp