Dishwasher drain pump: signs of failure, testing and replacement

The drain pump pumps the dirty water out of the sump at the bottom of the dishwasher and pushes it through the drain hose into the sink trap or the waste pipe. It runs several times per programme: after the main wash and after every rinse. The pump sits under the sump, covered by the filters — a coarse screen and a fine filter. On many machines there is a small plastic pump cover under the filter, and the pump impeller sits beneath it.

Almost every pump problem looks the same: water stays in the bottom after the programme, the machine stops and shows a drain error. Most often, though, the pump itself is fine and the cause is a blockage: broken glass, fruit stones, jar labels, clogged filters or a kinked hose. Below is how to tell a blockage from a faulty pump.

Call now

Signs of failure

  • water stands in the bottom of the machine after the programme or drains very slowly;
  • a drain error on the display: E24 or E25 on Bosch and Siemens, 5E/5C on Samsung, OE on LG, i20 on Electrolux, AEG and Zanussi, F11 on Miele;
  • the pump hums or squeals during draining but the water does not go — the impeller is jammed or the pump is worn;
  • you hear scraping or rattling — a piece of glass is in the pump or an impeller blade is damaged;
  • there is complete silence during draining — the pump gets no power or its winding has burnt out;
  • the machine smells of stale water;
  • water appears under the machine or in its base tray — a worn pump can crack and leak.

When this part fails: Not draining · Not cleaning dishes properly · Bad smell

How it is checked

Switch the machine off and unplug it before checking. Be careful: there may be sharp pieces of glass in the sump and the pump.

  1. Take out the lower basket and unscrew the filters. Rinse the screen and the fine filter under running water with a non-abrasive brush.
  2. Remove the water from the sump with a sponge or a cup.
  3. Find the pump cover under the filter. Lever it up with a spoon until it clicks and lift it out (Bosch and Siemens recommend exactly this for error E25). Check the impeller: it should turn freely, with no glass, stones or labels. Do not touch the impeller with your fingers if there is glass inside.
  4. Refit the cover and the filters until they lock — a cover that is not seated also causes a drain error.
  5. Check the drain hose: it must not be kinked or trapped under the machine. If the hose is connected to the sink trap, make sure the trap is not blocked. On a new trap or food waste disposer the blanking plug in the hose connector may still be in place — then no water drains at all.
  6. Run the Drain programme (or cancel the programme) and listen: the water should be gone within a few minutes.

What the technician checks:

  • whether the pump gets voltage during draining — if not, the cause is the wiring or the board;
  • the pump winding: an open circuit means replacement;
  • the impeller, housing and seals of the pump, and the non-return valve in the drain;
  • the level sensor or float — if the machine "sees" the water wrongly, it may not start draining or may stop with an error.

Repair and replacement

If the filters, the pump cover and the hose are clear but water still stands in the machine, or the pump only hums or stays silent, it needs replacing. To do that the machine is usually pulled out of its cabinet and the bottom panel removed, or it is laid on its side — without experience it is easy to damage the hoses or flood the floor. The technician fits a pump made for your exact model and checks for leaks after the first drain.

To make the new pump last longer:

  • scrape food scraps and stones off the dishes before loading;
  • remove labels from jars before washing them in the machine;
  • clean the filters every week or two, and straight away after a glass breaks in the machine.

A MasService technician comes to your home anywhere in Baku, checks the pump, the hose and the level sensor and names the price before starting the work.

Frequently asked questions

Why does water stay in my dishwasher after a wash?

Most often the filters or the sink trap are blocked, or the hose is kinked. If everything is clear but the pump hums or is silent, the pump itself or its power supply is faulty.

Is a little water in the bottom normal?

On many machines a small amount of water in the sump under the filter is normal: it keeps the seals moist. It is not normal if water stands above the filter or the machine shows a drain error.

Can I remove the drain pump cover myself?

Yes, on many models the manufacturer intends you to: after removing the filters, the cover is levered up with a spoon. Do it with the machine switched off and with care — there may be broken glass inside.

Could not fix it yourself? A technician comes to your home in Baku, finds the cause on site and names the price before the repair: Dishwasher repair

Call now WhatsApp