Dishwasher spray arms: signs of blockage, cleaning and replacement
Spray arms are the plastic arms with small holes (nozzles) that rotate inside the dishwasher tub. The circulation pump pushes water into them under pressure, the water leaves the nozzles in jets, and the recoil turns the arm by itself — so the jets sweep over all the dishes. Spray arms have no motor of their own: only the water pressure turns them.
There are usually two or three: the lower arm under the lower basket, the upper arm under the upper basket, and on many models a third, top arm above the cutlery rack. When the nozzles are blocked by food, bits of labels or limescale, or an arm does not turn, the water hits one spot and part of the load comes out dirty. This is one of the most common reasons for poor washing, and in most cases you can fix it yourself.
Signs of failure
- dishes come out poorly cleaned, especially in one basket or one area of the tub, with food left on the upper basket;
- sand, grains or small debris are left on the dishes after the wash;
- the arm is stiff to turn by hand, wobbles, sits crooked or touches the dishes or the basket;
- the arm is cracked, its end cap is missing, or its nut / clip is broken;
- the nozzles are blocked with white scale or food — you can see it by holding the arm up to the light;
- a Miele machine shows "Spray arm (bottom)" or a similar message for the upper arm;
- knocking during the wash: the rotating arm hits a tall item or a pan handle.
When this part fails: Not cleaning dishes properly · White residue on dishes · Noisy
How it is checked
Switch the machine off before checking. Remove the spray arms only with the machine off and after the programme has finished.
- Pull out the lower basket and turn the lower arm by hand. It should rotate freely and evenly. Push the loaded basket back in and turn it again — tall plates, trays and handles must not touch it.
- Remove the lower arm: on most machines you simply pull it upwards (on Bosch, unclip it and lift it away).
- Remove the upper arm: it is held by a nut or clip under the upper basket. Turn the nut in the direction of the arrow on it (on Bosch the arm is unscrewed) and take the arm down. On LG, the third top arm is held by clips on both sides — release them with a screwdriver and do not lose the pin.
- Clear every nozzle with a toothpick or a fine needle. Miele advises pushing food particles into the arm and then rinsing them out.
- Rinse the arm under hot running water, shake it and tap it gently on a table so debris falls out. Hold it up to the light — every hole should be clear.
- If the nozzles have white scale, Bosch recommends soaking the arms in a vinegar solution and then always washing them in soapy water and rinsing.
- Refit the arms until they click (turn the upper nut until it locks) and check that each one turns freely.
- Clean the filter in the bottom of the tub at the same time: a blocked filter lowers the pressure and the arms turn weakly.
What the technician checks:
- the arm's hub and its seat — a worn hub makes the arm wobble and tilt;
- the supply tube to the upper arm and its seals — if the joint leaks, water bypasses the nozzles;
- the water pressure: the circulation pump, its impeller and its power supply;
- the diverter valve (on models that feed the arms in turns).
Repair and replacement
If an arm is cracked, its nut or clip is broken, or its hub is loose, the part is replaced — gluing it does not work, a crack lowers the pressure. Spray arms are chosen strictly for the machine's model.
If the arms are clean, turn freely and the filter is clean, yet the dishes still come out dirty, the cause is deeper: a weak circulation pump, a blocked supply tube, a faulty diverter valve or water that does not heat. A technician checks this.
To keep the arms from blocking:
- scrape food, bones and grains off the dishes;
- remove labels from jars before washing them;
- take the arms out and rinse them together with the filter once a month;
- keep salt and rinse aid in the machine — they reduce limescale.
A MasService technician comes to your home anywhere in Baku, checks the spray arms, the pump and the water supply and names the price before starting the work.
Frequently asked questions
Why are the dishes in the upper basket dirty while the lower ones are clean?
Most often the upper spray arm is blocked or not turning, or its nut has come loose. Remove it, clear the nozzles and check that it turns freely. If that does not help, the supply tube and the pump are checked.
Can I remove and clean the spray arms myself?
Yes, manufacturers (LG, Bosch, Miele) describe it in their instructions: the lower arm lifts off, the upper arm is turned off in the direction of the arrow. Do it with the machine switched off.
How often should the spray arms be cleaned?
Manufacturers do not give an exact interval; it makes sense to check them once a month together with the filter, and straight away when the dishes start coming out dirtier.
Other parts
Dishwasher repair — Brands
Could not fix it yourself? A technician comes to your home in Baku, finds the cause on site and names the price before the repair: Dishwasher repair