Dishwasher heating element: how it works, signs of failure and testing

The heating element heats the water the dishes are washed in. Without hot water the detergent works poorly, grease stays on and the dishes come out wet.

Dishwashers use two kinds of heater. An exposed element is a thin circular tube in the bottom of the tub, visible once the lower basket is out. A hidden (flow-through) heater sits under the floor next to the sump or in the pump housing and heats the water as it passes through. Many Electrolux, AEG and Zanussi machines use this type.

In Bosch and Siemens dishwashers the heater is built into the circulation pump — Bosch calls the unit the "heat pump". Its heater fault shows as E09, and the unit itself is described on the circulation pump page.

Call now

Signs of failure

  • dishes, especially greasy ones, do not come clean — the water stays cold;
  • the dishes are wet and cold at the end of the programme;
  • the programme runs much longer than usual or stops halfway — the machine is waiting for the water to heat;
  • a heating code on the display: HE on Samsung and LG, i60 on Electrolux, AEG and Zanussi, H7 on Beko, F10 on Indesit;
  • cracks, blisters, dark spots or a thick limescale layer on an exposed element;
  • the breaker or RCD trips while heating — current may be leaking through a damaged element.

When this part fails: Not heating water · Not cleaning dishes properly · White residue on dishes · Not drying dishes

How it is checked

Unplug the machine before any inspection. If it has just run, let it cool: the element gets very hot.

  1. Choose a programme with heating (not a short cold one) and check whether the dishes are warm at the end. Some programmes barely heat the water.
  2. Clean the filters and remove food scraps from the tub floor: with too little water many machines do not switch the heater on.
  3. If your machine has an exposed element, take out the lower basket and look at it. Cracks, blisters and burn marks mean a technician is needed. A thick white coating is limescale.
  4. Check the salt and the water hardness setting. Electrolux warns that with hard water and a wrong setting limescale builds up on the heater over time. Add salt even if you use all-in-one tablets.
  5. Reset the error as your manual describes (switch off, wait, switch on) and run the programme again.

What the technician checks:

  • the element's resistance with a multimeter, terminals disconnected: an open or short circuit means the element is faulty;
  • the element's insulation to earth with a dedicated tester — an ordinary multimeter often misses the leak;
  • the temperature sensor (NTC) and thermostat: when they fail, the machine does not heat either;
  • the heater relay on the control board and the wiring to the element;
  • on flow-through heaters, the pressure switch and the water flow through the heater.

Repair and replacement

Call a technician if the water stays cold after checking the programme, filters and salt, if the heating code comes back or if the machine trips the breaker. AEG advises not using the machine until the heating is repaired: without hot water the dishes do not get clean.

A faulty element is not repaired but replaced with one that fits the model; a flow-through heater is replaced as a complete unit. After the replacement the technician checks heating on a full programme. To keep the new element free of limescale, keep the salt and hardness setting right.

A MasService technician comes to your home in any district of Baku, finds the cause and names the price before starting work.

Frequently asked questions

How do I know the dishwasher heating element has failed?

Dishes do not come clean or dry, the programme runs longer than usual or stops, and a heating code may appear (HE, i60, H7, F10). A multimeter test confirms it.

Why does my dishwasher trip the breaker?

One possible cause is a damaged heating element leaking current to the casing while it heats. Do not keep using it: switch it off and call a technician.

Where is the heating element in a Bosch dishwasher?

In Bosch and Siemens the heater is built into the circulation pump. When it does not heat, the machine shows E09 and the whole pump-and-heater unit is replaced.

Could not fix it yourself? A technician comes to your home in Baku, finds the cause on site and names the price before the repair: Dishwasher repair

Call now WhatsApp