Dishwasher stops mid-cycle: causes and what to check

The dishwasher started washing and then stopped: water is standing inside, the programme does not move on, or it will not let you pick another one. Manufacturers name a few simple causes: Bosch — a door that is not closed properly and an interrupted power or water supply; JennAir — a door opened during the cycle, a power cut and drainage problems; Electrolux — a programme that is already running and has to be reset.

If the panel is flashing or the display shows an error code, look up its meaning in our code database first: it shows at once where to look.

Call now

Likely causes

  • the door is not closed properly — the dishwasher stops the programme (Bosch);
  • the door was opened during the wash and the programme was not restarted (JennAir);
  • something presses on the back panel, such as a hose holder that was not removed (Bosch);
  • the power or water supply was interrupted (Bosch, JennAir);
  • the dishwasher cannot drain: a clogged filter, a kinked or clogged drain hose, a blocked sink disposer, or a disposer knockout plug left in after installation (JennAir);
  • a programme is already running, so another cannot be selected — it has to be reset (Electrolux);
  • a fault the dishwasher reports with an error code (JennAir).

Safe steps you can try

  1. Look at the panel: if it is flashing or shows an error code, find its meaning in the manual or in our code database (JennAir).
  2. Shut the door firmly until the latch engages fully. If the door was opened during the wash, press Start and close the door — the programme resumes (Bosch, JennAir).
  3. Check that nothing presses on the back panel, such as a hose holder that was not removed during installation (Bosch).
  4. Make sure there is power and the water tap is open, then continue the programme (Bosch). After a power cut, JennAir advises holding Cancel so the dishwasher drains, then starting the programme again.
  5. If water is standing inside, check the drain: remove the filter and rinse it under running water, and check that the drain hose behind the unit is not kinked or clogged (JennAir).
  6. If the programme is stuck and will not let you choose another, reset it: press and hold the reset or cancel button (on Electrolux built-in models, the on/off button for about 3 seconds), then switch the dishwasher off and on (Electrolux).
  7. Reset the power: unplug the dishwasher for 30 seconds or switch off its circuit breaker for 30 seconds, then switch it back on (JennAir).

When to call a technician

Call a technician if the dishwasher stops again after these checks, does not drain with a clean filter and a straight hose, shows the same error code, or if the power drops on its own socket (Bosch advises contacting an electrician in that case). The cause may be the door lock, the drain pump, the inlet valve or the control board.

A MasService technician will check the dishwasher on site and name the price before starting the repair.

Frequently asked questions

Why does my dishwasher stop when the door is closed?

Bosch says the dishwasher will stop if the door is not closed properly: the latch has to engage fully. Also check that nothing presses on the back panel, such as a hose holder that was not removed.

What should I do if the dishwasher stopped after a power cut?

Bosch advises restoring the power and water supply and continuing the cycle. JennAir advises holding Cancel so the dishwasher drains, then starting a new cycle.

The dishwasher stopped with water inside — what should I check?

JennAir links this kind of stop to drainage: rinse the filter under running water, check that the drain hose is not kinked or clogged, and if the dishwasher is connected to a sink disposer, that it is clear.

Could not fix it yourself? A technician comes to your home in Baku, finds the cause on site and names the price before the repair: Dishwasher repair

Call now WhatsApp